Support our Sponsors, they keep FADU free: AG Photographic The Imaging Warehouse Process Supplies RH Designs Second-hand Darkroom Supplies |
> Electrical help: Durst Laborator 1200/CLS450 Head. |
*** Click here for the FADU 2015/2014 Yearbooks *** |
|
Thread Tools | Search this Thread | Display Modes |
#1
|
|||
|
|||
Electrical help: Durst Laborator 1200/CLS450 Head.
I just won a Durst Laborator 1200 with CLS450 dichromat head for £1.20 on ebay. Fortunately it is in Plymouth about 4 miles from me so no issue with collection.
The seller has stated that the transformer/timer has a problem and it blows lamps immediately. It sounds to me like the transformer windings might have shorted out through damp/corrosion. Doesn't the transformer only power the lamp? If so, wouldn't any transformer 240V in 24V out with sufficient power capabilities 10A be okay (like this one 240V-24V 10A) when used with a timer (which again is basically just a timed switch? TIA for any assistance. Last edited by EdBray; 29th June 2013 at 07:01 PM. |
#2
|
||||
|
||||
You don't need anything that complicated to run a lamp. That is a switch mode power supply. You just need a transformer.
However... they are much cheaper than a transformer so probably worth a go. Steve. |
#3
|
|||
|
|||
Thanks Steve, that is my take on it too.
I would like to use it with my Analyser Pro but don't want to do anything that may put it at risk. |
#4
|
|||
|
|||
Hi Ed,
Take the 4 screws out of the power supply and look for an exploded blue capacitor. You will have to double the cost of your enlarger to £2.40 though as the part is £1.20. Its easy to find the part on ebay. I was going to buy that Enlarger from the seller directly but he wouldn't pack it! I have a new CLS500 head and Durst Power Supply for that Enlarger if you want to make an offer, but alas, as its my only spare, I cant let it go for £1.20.. |
#5
|
|||
|
|||
Thanks Marc, I'll have a look tomorrow after I collect the Enlarger, I assume the capacitor is an electrolytic, if it's exploded how will I discover its value?
|
#6
|
|||
|
|||
Screw Driver
Take some good photos of the bit thats blown up and I'll lift the lid on mine and read them off for you.
|
#7
|
|||
|
|||
Outstanding Marc, that would be great.
|
#8
|
|||
|
|||
And then we can update your About me page.
|
#9
|
|||
|
|||
|
#10
|
|||
|
|||
Just had a look at the ebay listing - That looks like a Rayco stabiliser/timer unit. Pretty crude by modern standards, but most of the internal components are still available.
I would suggest the first thing to replace is the ceramic lamp holder inside the head. Then measure the voltage across the two pins before risking another lamp. If it is still causing trouble, we can dig a little deeper. |
Support our Sponsors, they keep FADU free: AG Photographic The Imaging Warehouse Process Supplies RH Designs Second-hand Darkroom Supplies |
Thread Tools | Search this Thread |
Display Modes | |
|
|
Similar Threads | ||||
Thread | Thread Starter | Forum | Replies | Last Post |
Durst L1200: Laborator 1200 5x4 Enlarger | Xpres | Articles | 11 | 21st January 2019 10:57 AM |
Durst Laborator 1200/CLS450 not working - please help! | Brock | Darkroom | 18 | 1st October 2011 09:05 PM |
Looking for Durst VLS 501 varicontrast head for my Laborator 1200 | Adrian Holmes | Darkroom | 15 | 19th February 2011 07:51 AM |
Durst Laborator 1200 and ILFOSPEED Multigrade System | Martin Aislabie | Auctions of Interest | 2 | 13th February 2011 08:31 PM |
Durst Laborator 1200 | Neil Smith | Auctions of Interest | 10 | 19th November 2010 07:32 AM |