Support our Sponsors, they keep FADU free: AG Photographic The Imaging Warehouse Process Supplies RH Designs Second-hand Darkroom Supplies |
> Imperial to metric enlarger lens adaptor |
*** Click here for the FADU 2015/2014 Yearbooks *** |
|
Thread Tools | Search this Thread | Display Modes |
#1
|
|||
|
|||
Imperial to metric enlarger lens adaptor
I have a 1 1/2" - 24tpi mounting ring for a Wray lens
I have 39mm [26tpi] standard mounting rings [1 1/2" is 38.1mm, the root diameter of the 39mm rings is 38.02mm] However, the outside diameter of the Wray lens' 1 1/2" thread is the same as or slightly smaller than the threaded bore of the 39mm ring. In addition the lenght of the male and female threads is very short so the difference betwene 26 and 24tpi is of little effect. Using masking tape I can get the Wray lens to fit into the standard 39mm ring BUT it tends to come loose. Also I cannot satisfactorily unscrew and re-screw it into the 39mm ring. Does anyone have any suggestions for long-lasting methods of 'increasing' the 1 1/2" thread so that it can be screwed into and out of the 39mm ring many times. The reason for asking is that I have a 50mm and 150mm lens that both have 39mm threads, but the mid-sized 108mm [4 1/4"] Wray lens has the 1 1/2" thread. It has been suggested that SRB could make an adaptor - that do 1 1/4" to 39mm - I have yet to contact them. regards |
#2
|
|||
|
|||
I wonder if PTFE tape as used by plumbers on threaded fittings would be OK.
It will not last forever if being screwed and unscrewed umpteen times, but it may last longer than masking tape. It is cheap and easy to get in d.i.y. shops. Or cadge some off a friend to see if it works before buying a roll. Cheers.
__________________
It will all be over by Christmas. |
#3
|
|||
|
|||
Good thought Nat Certainly on metal pipes I found that PTFE tape would allow me at least a couple of screwing and unscrewing and after this number I tended to replace because its purpose was to prevent water leaks. It is much thinner and more flexible stuff than masking tape and quite cheap
Tony, in your case where water leaks aren't a consideration you might well find it works OK for several more screws and unscrews I suppose key to this is how frequently this needs to be done Mike |
#4
|
||||
|
||||
Hi Tony
Only a suggestion - but do you have a local machine shop that could make you an adapter ring/tube ? Have one end machined for the Wray and the other for the 39mm thread. Another solution is to have a locking flange machined - push the lens through the 39mm plate and then screw on the locking wring for the Wray. Some large enlarger lenses (LF/ULF) have used locking flanges as their mounting method. Best of luck Martin |
#5
|
|||
|
|||
Quote:
regards |
#6
|
|||
|
|||
Whilst the following idea is very much Heath Robinson it may get you out a spot until you can get a decent lens panel or adaptor made.
My idea is to use the enlarger red filter holder beneath the lens as a support to stop your lens from wobbling. When I tried it on my lens it still allowed the aperture adjusting ring to turn on the lens. I do not use the red filter, but used to use the holder for a diffuser on a colour analyser. Hence the frosted plastic instead of red filter. The brownish filter is meant to represent a hole cut into a plywood or plastic disc. The hole then allows the image to pass through and the plywood disc supports the lens. Very crude I know, but it should work until you get sorted with something purpose made. Have a look at the pictures. The frosted disc represents a plastic or ply or metal disc with a hole cut in it big enough to support the lens. The brownish filter represents the hole to let the light through. The final image is the support in situ. Good Luck and Cheers. http://www.film-and-darkroom-user.or...1&d=1601841337 http://www.film-and-darkroom-user.or...1&d=1601841337 http://www.film-and-darkroom-user.or...1&d=1601841337
__________________
It will all be over by Christmas. |
#7
|
|||
|
|||
Quote:
regards Tony |
#8
|
|||
|
|||
I have just made a lens mount and 3d printed it for my Opemus 6 ..
Flack |
#9
|
|||
|
|||
Quote:
Terry S |
#10
|
||||
|
||||
I had a very good adaptor made at a very reasonable price from
https://customphototools.com/contact/ Very good work.
__________________
www.eleventyoneportraits.com |
Support our Sponsors, they keep FADU free: AG Photographic The Imaging Warehouse Process Supplies RH Designs Second-hand Darkroom Supplies |
Thread Tools | Search this Thread |
Display Modes | |
|
|
Similar Threads | ||||
Thread | Thread Starter | Forum | Replies | Last Post |
Camera lens as Enlarger lens | kennethcooke | Cameras - small format | 9 | 3rd May 2022 08:51 AM |
M42 - Olympus OM adaptor | Rob Archer | Cameras - small format | 11 | 8th December 2017 08:19 AM |
Multigrade 500 adaptor to 504 | Xpres | Sale or Wanted | 5 | 7th September 2013 09:06 AM |
Enlarger lens needs an MOT! | SimonNOTTS | Darkroom | 12 | 25th January 2013 07:05 PM |
WTB M/F Enlarger Lens | kennethcooke | Sale or Wanted | 5 | 18th June 2012 07:57 PM |