Support our Sponsors, they keep FADU free: AG Photographic The Imaging Warehouse Process Supplies RH Designs Second-hand Darkroom Supplies |
> First darkroom, I think I've ordered everything I need |
*** Click here for the FADU 2015/2014 Yearbooks *** |
|
Thread Tools | Search this Thread | Display Modes |
#11
|
|||
|
|||
When I used the bathroom as a temporary darkroom I had a board over the bath for the enlarger and trays.
The advice in those days was to run a few inches of water into the bath in case of any un-noticed chemical splashes. It immediately diluted any chemical spills and prevented the bath from getting stained. I have no idea on modern electrical safety regulations for use in bathrooms, but if you are using an extension lead to power the enlarger, a Residual Circuit Breaker plug would be a very desirable safety precaution.
__________________
It will all be over by Christmas. |
#12
|
||||
|
||||
Quote:
Sent from my ONEPLUS A6013 using Tapatalk |
#13
|
|||
|
|||
As posted by others before, the red LED lamps (screw or bayonet) sold for parties and other decoration make superb safelights for Multigrade - bright and really safe.
RCD is essential, often now sold for garden stuff. Test often as per instructions. Make sure the enlarger is earthed, preferably with a 13A plug - no adapters. |
#14
|
||||
|
||||
Quote:
Sent from my SM-T810 using Tapatalk |
#15
|
|||
|
|||
ENLARGER EARTH.
My enlarger is a Durst M605. Just had a look at the electrics. There are only two conductors in the original cable that goes to the transformer from the mains supply. The transformer in turn only has two conductors going to the lamp holder in the enlarger head. So there is no earth supply at all. I even put a multi-meter set for continuity testing, between the head and the vertical column. There was no connection there between the head and column. When I had a closer peek I could see the head slides along the column in nylon shoes. Slim chance of connection there. It is POSSIBLY double insulated. Not being an electrician I have no idea if adding an earth to a double insulated piece of equipment is dangerous or not. If any qualified electricians are reading this please let us know if it is dangerous to add an earth to double insulated equipment. Assuming it is double insulated. And UK electrics. Cheers.
__________________
It will all be over by Christmas. |
#16
|
|||
|
|||
Earths on enlargers used to be recommended, not only for safety but also to reduce dust attracting static electricity.
Cheers.
__________________
It will all be over by Christmas. |
#17
|
||||
|
||||
My enlarger being such a basic one is literally a desk lamp inside a box with a condenser lens.
I can even pull the lamp holder out. I'll take some pictures. Sent from my ONEPLUS A6013 using Tapatalk |
#18
|
||||
|
||||
There's a lot of exposed metal on an F30. Safety was not always uppermost on designer's minds back in the day, so I agree an earth is well worth adding.
Saying that, an RCD should prevent electrocution in the unlikely event of the metal becoming live, but you get no warning as it will not trip until you touch the live metal - had it been earthed, it would trip immediately the short occurred and will refuse to be reconnected until the fault is cleared. A fairly recently (re)wired house will have at least one RCD in the consumer unit. Colour enlargers with a transformer may not need one as the voltage is stepped down to 12 or 24 volts via an isolating transformer and that is not enough to push a dangerous amount of current through the human body. Even then, a fault in the transformer can put 240V on the output instead of 12/24V (a typical failure mode for cheap USB chargers - NEVER buy cheap USB chargers!) so it's still worth having as a belt-and-braces addition but by no means essential. A colour enlarger with separate low-voltage power supply is a "Class III" device and is considered safer in this regard than "double insulated" (Class II). The double-insulated device should have either the class designation or the double-insulated symbol (one rectangle inside another) on the label. Last edited by Bob; 9th August 2020 at 03:18 PM. |
#19
|
||||
|
||||
Thanks Bod, I wouldn't know how to go about earthing it if it wasn't designed that way.
The enlarger is double insulated, the live can never come in contact with the metal part unless the cable has a cut in it. Last edited by Britman; 9th August 2020 at 02:54 PM. |
#20
|
||||
|
||||
Quote:
Enjoy (finally! ). |
Support our Sponsors, they keep FADU free: AG Photographic The Imaging Warehouse Process Supplies RH Designs Second-hand Darkroom Supplies |
Thread Tools | Search this Thread |
Display Modes | |
|
|
Similar Threads | ||||
Thread | Thread Starter | Forum | Replies | Last Post |
can I use what I learned in a b&w darkroom in a color darkroom | cndnlfartist | Colour printing techniques | 8 | 17th November 2015 03:14 AM |